Skip to main content
Login Contact Us

SFP-ETH-10-RT-W15-LC

1310 nm / 1.25 Gb/s Single Mode SFP Transceiver

The SFP-ETH-10-RT-W15-LC is a single mode optical transceiver that supports signals up to 1.25 Gb/s for bidirectional serial data communications such as 1000BASE-BX10.

FEATURES

  • 1-Fiber Bidirectional Transceiver
  • SFP MSA compliant
  • 1.25 Gb/s:
    • 1000BASE-BX10 compliant
  • 1550 nm DFB LD Transmitter
  • 1310 nm receiver
  • Link distance up to 10 km at 1.25 Gb/s 
  • RoHS compliant
  • Hot pluggable
  • Diagnostic Monitoring Interface (DMI)

SPECIFICATIONS

Transmitter Specifications (-10°C < Tc < 85°C, 3.1V < Vcc < 3.5V)

Parameter

Symbol

Min.

Typ.

Max.

Units

Notes



Optical

Optical Transmit Power

Po

-9

-3

dBm

Output power is power coupled into a 9/125 µm single mode fiber

Output Center Wavelength

λ

1480

 

1580

nm

 
Output Spectrum Width

Δ λ

1

nm

-20 dB width

Side Mode Suppression Ratio

SMSR

30

 

 

dB

 
Extinction Ratio

ER

9

dB

 
Optical Rise Time

tr

 

 

260

ps

20% to 80% values

Optical Fall Time

tf

 

 

260

ps

20% to 80% values

Relative Intensity Noise

RIN

 

 

-120

dB/Hz

 



Electrical

Data Input Current – Low

IIL

-350

 

 

µA

 
Data Input Current – High

IIH

 

 

350

µA

 
Differential Input Voltage

VIH -VIL

0.5

 

2.4

V

Peak-to-peak

TX Disable Input Voltage – Low

VTDIS, L

0

 

0.5

V

There is an internal 4.7 kΩ to 10 kΩ pull-up resistor to VccTX

TX Disable Input Voltage – High

VTDIS, H

2.0

 

Vcc

V

TX Disable Assert Time

TASSERT

 

 

10

µs

 
TX Disable De-assert Time

TDEASSERT

 

 

1

ms

 
TX Fault Output Voltage – Low

TFaultL

0

 

0.5

V

Open collector compatible, 4.7 kΩ to 10 kΩ pull-up to Vcc (Host Supply Voltage)

TX Fault Output Voltage – High

TFaultH

2.0

 

Vcc+0.3

V



Receiver Specifications (-10°C < Tc < 85°C, 3.1V < Vcc < 3.5V)



Optical

Sensitivity

Sens

 

 

-20

dBm

Measured at 27-1 PRBS at BER 1E-12 @1300 nm

Maximum Input Power

Pin

-3

 

 

dBm

Signal Detect – Asserted

Pa

-20

dBm

Transition: low to high

Signal Detect – De-Asserted

Pd

-31

dBm

Transition: high to low

Signal detect – Hysteresis

 

1.0

 

dB

 
Wavelength of Operation  

1260

1360

nm

At least 30 dB optical isolation for the wavelength 1480 to 1580 nm

Optical Return Loss

ORL

14

 

 

dB

 



Electrical

Differential Output Voltage

VOH – VOL

0.6

 

2.0

V

 
Output LOS Voltage – Low

VOL

0

 

0.5

V

Open collector compatible, 4.7 kΩ to 10 kΩ pull-up to Vcc (Host Supply Voltage)

Output LOS Voltage – High

VOH

2.0

 

Vcc+0.3

V

Note: Only connections with patch cords with PC or UPC connectors are supported.

ORDERING INFORMATION

Part number

Bit Rate (Gb/s)

1000 BASE

Distance (km)

Wavelength (nm)

Package

Temp. (°C)

Tx Power (dBm)

Rx Sens. (dBm)

RoHS Compliant

SFP-ETH-10-RT-W15-LC

1.25

BX10

10

1550 DFB

SFP with DMI

0 to 70

-9 to -3

-20

Yes

Note: Only connections with patch cords with PC or UPC connectors are supported.

DOCUMENTS & DOWNLOADS

DATASHEETS

Small Form-factor Pluggable (SFP) Optical Module Cartridges (Ethernet)

The Small Form-factor Pluggable (SFP) optical module cartridges are small, hot-pluggable devices used to provide Ethernet fiber connectivity to IP-based products from either a Densité frame or Grass Valley/Telecast standalone fiber products. Multimode fiber links can be used for links of a few hundred meters, while single-mode fiberlinks can be used at distances up to 10 kilometer and over (dependent on SFP type) without degrading signal quality.

Download
Go back to top