SFP-ETH10G-RT-W27-LC
1-Fiber WDM / 10.3 Gb/s Single Mode SFP Transceiver
The SFP-ETH10G-RT-W27-LC is a single mode optical transceiver that supports signals up to 10.5 Gb/s for bidirectional serial data communications over a single fiber.

FEATURES
- 1-fiber bidirectional transceiver
- SFP+ MSA compliant
- 10GBASE-BX compliant
- 10.5 Gb/s:
- 1270 nm multiple quantum well LD transmitter
- RoHS-6 compliant
- Hot pluggable
- Link distance up to 10 km at 10.3 Gb/s
- Diagnostic Monitoring Interface (DMI)
SPECIFICATIONS
Specifications (0°C < Tc < 70°C, 3.13V < Vcc < 3.47V) |
||||||
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Units |
Notes |
Transmitter Optical Specifications |
||||||
Average Launch Power |
Po, AVG |
-5 |
— |
0 |
dBm |
Output power is power coupled into a 9/125 µm single mode fiber |
Output Center Wavelength |
λ c |
1260 |
1270 |
1280 |
nm |
|
Output Spectrum Width |
σ λ |
1 |
nm |
-20 dB width |
||
Side Mode Suppression Ratio |
SMSR |
30 |
dB |
|||
Relative Intensity Noise |
RIN |
-128 |
dB/Hz |
|||
Average Launch Power of OFF transmitter |
-30 |
dBm |
||||
Receiver Optical Specifications |
||||||
Sensitivity at 10.3 Gb/s |
-14 |
dBm |
Measured with average power;
BER < 10-12 and PRBS 231-1
|
|||
Receiver Overload |
PMAX |
0.5 |
— |
dBm |
||
LOS – De-Asserted |
LOSD |
— |
— |
-16 |
dBm |
Transition: low to high |
LOS – Asserted |
LOSA |
-26 |
— |
— |
dBm |
Transition: high to low |
Wavelength of Operation |
λ c |
1320 |
1340 |
nm |
At least 30 dB optical isolation for the wavelength 1260 to 1280 nm |
|
Electrical Characteristics |
||||||
High-Speed Signal (CML) Interface Specification |
||||||
Input Data Rate |
10.3125 |
Gb/s |
||||
Differential Input Impedance |
Rin |
100 |
Ω |
|||
Differential Data Input Amplitude |
150 |
1000 |
mVp-p |
Internally AC coupled |
||
Output Data Rate |
10.3125 |
Gb/s |
||||
Differential Output Impedance |
Rout |
100 |
Ω |
|||
Differential Data Output Amplitude |
350 |
600 |
700 |
mVp-p |
Internally AC coupled |
|
Low-Speed Signal (LVTTL) Interface Specification |
||||||
Input High Voltage |
2.0 |
Vcc+0.3 |
V |
|||
Input Low Voltage |
GND |
0.8 |
V |
|||
Output High Voltage |
2.4 |
Vcc |
V |
|||
Output Low Voltage |
GND |
0.5 |
V |
Note: Only connections with patch cords with PC or UPC connectors are supported.
MEDIA GALLERY

ORDERING INFORMATION
Part number |
Bit Rate (Gb/s) |
Distance (km) |
TX (nm) |
RX (nm) |
Package |
Temp. (°C) |
RoHS Compliant |
SFP-ETH10G-RT-W27-LC |
10.3 |
10 |
1270 DFB |
1330 |
SFP+ with DMI |
0 to 70 |
Yes |
Note: Only connections with patch cords with PC or UPC connectors are supported.
WDM units are only available on special request. Lead time is usually 6 to 8 weeks ARO.