Skip to main content
Contact Us

IQUCP25 GATEWAY & MV APPLICATIONS

Universal Compute Processor for 25 GbE IP Systems

The IQUCP25 is a user configurable multichannel video-over-IP transceiver developed for use within low-latency and high-bandwidth Ethernet IP networks. Using RTP VSF TR-03 (SMPTE ST 2110), TR-04 and SMPTE ST 2022-6 encoding and encapsulation schemes, along with either clause 74 or clause 108 FEC, enables the IQUCP25 to encode or decode up to 16 SDI signals and transport them over redundant 25 GbE links (SMPTE ST 2022-7).

To enable hardware processing flexibility, IQUCP25 has a variety of Software Defined Cores (SDCs) available that can be purchased and loaded as operational needs demand. SDCs can be installed via a licensing...

FEATURES

General Features
  • Supports configuration of Ethernet links for maximum signal transport using both SFPs or for dual-link mode to provide link redundancy as per SMPTE ST 2022-7, and when operating as a receiver will dynamically adapt to any stream presented to it
  • Supports unicast as well as IGMPv3 source-specific multicast, allowing point-to-point operation or transmission in multicast groups, and forward error correction with either clause 74 (Base-R) or clause 108 (RS) FEC
  • Standards supported:
    • 3G-SDI to SMPTE ST 424/425 level A compatible
    • HD-SDI to SMPTE ST 292/274/296
    • SD-SDI to SMPTE ST 259-C
    • 25 GbE Ethernet to IEEE 802.3
  • RollCall control and monitoring compatible with standard logging and reporting features

 

Essence Processing (EP) Features
  • Handles up to 16 SDI signals over dual 25 GbE IP links (dependent on SDI signal format and compressed or uncompressed transport mode)
  • Multiple transport types available for each SDI input including:
  • Compressed IP transport using SMPTE ST 2042 (VC2) low- latency high-quality encoding profile
  • Uncompressed video transport using either VSF TR-03 (SMPTE ST 2110) and TR-04 RTP, or SMPTE ST 2022-6 encapsulation
  • PCM audio using TR-03 & AES67
  • SMPTE ST 2110-40 metadata support via IETF standard “RTP Payload for Ancillary Data”
  • Supports frame-synchronized SDI inputs and outputs, with audio rate adaption, referenced to either IEEE-1588v2 (PTP) network timing (compliant with SMPTE ST 2059-2) or via the IQH3B frame analog reference bus for blackburst/tri-level syncs
  • Includes UHD quad link mode for 3G SQD or 2SI signal transport
  • Low delay mode and independent H & V offset available for each channel along with up to two frames of video delay, and up to 255 ms of audio delay

 

Signal Monitoring (SM) Features
  • 12x4 multiviewer capability with signal monitoring license

SPECIFICATIONS

Inputs and Outputs

Signal Inputs/Outputs
SDI: 16x bidirectional, see configuration table
Electrical:

  • 3 Gb/s SDI, SMPTE ST 424
  • 1.5 Gb/s HD-SDI, SMPTE ST 292
  • 270 Mb/s SDI, SMPTE ST 259-C

Connector/format: HD-BNC/75Ω panel jack on standard connector panel

Ethernet Signal

SFP+ Optical: 2x 25 GbE Ethernet

  • Conforms to: IEEE 802.3by – 25 GbE over fiber

SFP+ connected cable: 2x 25 GbE Ethernet

  • Conforms to: IEEE 802.3 – 25 GbE over twinaxial cables

Note: SFP type must be ordered in addition to the module.

 

Controls

Indicators
Power: OK (Green)
CPU: OK (Flashing)
Content Status
Summary: OK (Green)    

  • Warning (Yellow)
  • Error (Red)
Electrical

Standards supported: 1125 (1080)/50p (A), 1125 (1080)/59p (A), 750 (720)/50p, 750 (720)/59p, 1125 (1080)/25i, 1125 (1080)/29i, 625 (576)/25i, 525 (480)/29i

Power Consumption
Module power consumption: 34.5 PR (B Frames)

Essence Processing SDI to IP Configurations:
IQUCP25 – 25 GbE Config 1 Config 2 Config 3 Config 4 Config 5
SDI In <> Out 16 > 0 0 > 16 12 > 4 4 > 12 8 > 8
Codec Support SMPTE ST 2022-6
TR-03 (SMPTE ST 2110)
TR-04
SMPTE ST 2022-6
TR-03 (SMPTE ST 2110)
TR-04
SMPTE ST 2022-6
TR-03 (SMPTE ST 2110)
TR-04
SMPTE ST 2022-6
TR-03 (SMPTE ST 2110)
TR-04
SMPTE ST 2022-6
TR-03 (SMPTE ST 2110)
TR-04
IQUCP25 – 25 GbE Config 6 Config 7 Config 8 Config 9  
SDI In <> Out 4 > 4 8 > 0 0 > 8 8 > 0  
Codec Support VC2 VC2 VC2 SMPTE ST 2022-6
TR-03 (SMPTE ST 2110)
TR-04
Frame Sync I/Ps
 

ORDERING INFORMATION

Order codes for IQH enclosures*

IQUCP2500-2B3
Universal Compute Processor. 16 SDI I/O, 2x 25 GbE I/O on SFP+ connectors. Suitable for IQH1A and IQH4B frames
IQUCP2501-3B3
Universal Compute Processor. 16 SDI I/O, 2x 25 GbE I/O on SFP+ connectors. Includes IQFAN rear panel for additional cooling in IQH3B frame

Software Defined Core Licenses

IQUCP-EP
Essence processing license for SDI to/from IP with synchronization and audio rate adaptation
IQUCP-MV
Signal monitoring license, includes 12x4 multiviewer functionality

SFP Options

FCS-25GE-SR
25GBASE-SR short range SFP for MMF
FCS-25GE-LR
25GBASE-LR long range SFP for SMF

Note: Fiber SFP type must be ordered in addition to the module.

* Although IQ modules are interchangeable between enclosures, their rear panels are enclosure specific. Order codes ‘A’ or ‘B’ may be used when installing modules in a ‘B’ enclosure. However, order code ‘A’ must be used when installing modules in an ‘A’ enclosure. Please take time to ensure that the compatible order code is selected to match the chosen enclosure.

DOCUMENTS & DOWNLOADS

DATASHEETS

IQUCP25: Universal Compute Processor for 25 GbE IP Systems Datasheet

The IQUCP25 is a user configurable multichannel video-over-IP transceiver developed for use within low-latency and high-bandwidth Ethernet IP networks

Download

DOCUMENTATION LIBRARY

Further documents

Already know what you're looking for? Click the link below to access our full documentation library

Visit Library
Go back to top