• Handles up to 16 SDI signals over dual 25 GbE IP links (number of channels dependent on SDI signal format)
• SDI embed/de-embed of up to 4 audio flows per channel
• Multiple SDI standards and formats supported, including 12G Single-link & 2SI 1080p (3G) modes over Single-stream or Quad Stream SMPTE ST 2110
• Supports configuration of Ethernet links for maximum signal transport using both SFPs or for dual-link mode to provide link redundancy as per SMPTE ST 2022-7, and when operating as a receiver will dynamically adapt to any stream presented to it
• Supports IGMPv3 source-specific multicast, allowing transmission in multicast groups
• Supports frame-synchronized SDI inputs and outputs, with audio rate adaptation, referenced to either SMPTE ST 2059-2 PTP or via the IQH4B frame analog reference bus for blackburst/trilevel syncs
• Fast, clean and quiet switching via make-before-break or break-before-make
• Low delay mode and independent H & V offset available for each channel along with up to two frames of video, and up to 255 ms of audio delay
• Seamless integration with GV Orbit Control, Configuration & Monitoring software, including logging and reporting
• SMPTE ST 2022-7 Class A & D seamless protection switching
• SMPTE ST 2059-1 & -2 precision time protocol
• NMOS IS-04 discovery and registration with group hints tag support
• NMOS IS-05 device connection management
• In-band or out-of-band control of NMOS
  Support of DHCP, LLDP and DNS-SD for easy IP configuration
• Both FC-FEC (Fire Code) and RS-FEC (Reed Solomon IEEE) Forward Error Correction are supported
• Dual SFP28 Flexible Ethernet for 25 GbE SFP28 cage:
  
  • SFP-25G-SR for short-range multimode optical connections
  • SFP-25G-LR for long-range single-mode optical connections
  • 10GBASE-SR for short-range multimode optical connections supported for
  • IQUCP-MD essence only
    10GBASE-LR for long-range single-mode optical connections supported for IQUCP-MD essence only

• SMPTE ST 2110-20 video including UHD Single-stream
• SMPTE ST 2110-21 Wide/Narrow profile receivers and Narrow senders
• SMPTE ST 2110-30 PCM audio
• SMPTE ST 2110-40 metadata associated with SMPTE ST 2110-20 video stream
• SMPTE ST 2022-6 Transport of High Bit Rate Media Signals (HBRMT) (SDI) over IP Networks
  
  

• Handles up to 16 MADI signals (8 in & 8 out) over dual 10/25 GbE IP links, with the option to provide MADI link redundancy
• Audio delay per IP output stream of up to 128 ms
• Uncompressed PCM audio transport using SMPTE ST 2110-30
• Audio tone generator available for MADI channels, with selectable tone frequencies of 1 kHz, 2 kHz, 4 kHz and 8 kHz
• Audio channel selection per IP stream from 1-64 channels, plus packet time selection of 125 µs, 250 µs, 500 µs, 1 ms and 4 ms
• Source/destination audio channel shuffling

IQUCP2504-2B3

IQUCP25 Universal Compute Processor. Hybrid SDI/MADI & IP, 4x SDI I/O up to 12G and 12x SDI I/O up to 3G or 8 MADI input and 8 MADI outputs, 2x 25 GbE or 2x 10 GbE ports. Suitable for IQH4B frames

Note: at least one processing license must also be ordered

IQUCP2505-3B3

IQUCP25 Universal Compute Processor. Hybrid SDI/MADI & IP, 4x SDI I/O up to 12G and 12x SDI I/O up to 3G or 8 MADI input and 8 MADI outputs, 2x 25 GbE or 2x 10 GbE ports.

Note: at least one processing license must also be ordered (Includes IQFAN00-RP for additional cooling in IQH3B frame)

IQUCP-EP
Essence processing license for SDI to/from IP with synchronization and audio rate adaptation

IQUCP-MD
Essence processing license for MADI to/from IP for IQUCP25 with 25G or 10G SFPs

FCS-25GE-SR
25GBASE-SR short range SFP for MMF

FCS-25GE-LR
25GBASE-LR long range SFP for SMF

FCS-10GE-SR
10GBASE-SR short range SFP for MMF (multimode fiber) supported for IQUCP-MD essence only

FCS-10GE-LR
10GBASE-LR long range SFP for SMF (single-mode fiber) supported for IQUCP-MD essence only

Note: Fiber SFP type must be ordered in addition to the module.

* Although IQ modules are interchangeable between enclosures, their rear panels are enclosure specific. Order codes ‘A’ or ‘B’ may be used when installing modules in a ‘B’ enclosure. However, order code ‘A’ must be used when installing modules in an ‘A’ enclosure. Please take time to ensure that the compatible order code is selected to match the chosen enclosure.