IQUCP50 GATEWAY & MV APPLICATIONS
Universal Compute Processor for 50GbE IP Systems
The IQUCP50 is a user-configurable multichannel video-over-IP transceiver developed for use within low latency and high bandwidth Ethernet IP networks. It can encapsulate or de-capsulate up to 16 SDI signals (depending on format) using either SMPTE ST 2110 or SMPTE ST 2022-6 encapsulation standards and transport them over redundant 50 GbE links (SMPTE ST 2022-7) with either dual or single port options providing “hitless” redundancy switching.
The IQUCP50 is a Universal Compute Processor offering low-latency, high-bandwidth multichannel broadcast processing/routing for SDI and IP applications. Delivering up 16 channels of 3G or four channels of UHD, this flexible powerhouse can adopt...

FEATURES
Key Features
- Handles up to 16 SDI signals over dual 50 GbE IP links with dual and single port rear panel options (number of channels dependent on SDI signal format)
- Multiple SDI standards and formats supported, including 12G Single-link & 2SI 1080p (3G) modes over Single-stream or Quad Stream SMPTE ST 2110
- Supports configuration of Ethernet links for maximum signal transport using both SFPs or for dual-link mode to provide link redundancy as per SMPTE ST 2022-7, and when operating as a receiver will dynamically adapt to any stream presented to it
- Supports IGMPv3 source-specific multicast, allowing transmission in multicast groups
- Supports frame-synchronized SDI inputs and outputs, with audio rate adaption, referenced to either SMPTE ST 2059-2 PTP or via the IQH4B frame analog reference bus for blackburst/trilevel syncs
- Fast, clean and quiet switching via make-before-break or break-before-make
- Low delay mode and independent H & V offset available for each channel along with up to two frames of video, and up to 255 ms of audio delay
- Seamless integration with GV Orbit Control, Configuration & Monitoring software, including logging and reporting
Essence Processing (EP) Features
- SMPTE ST 2110-20 video including UHD Single-stream
- SMPTE ST 2110-21 Wide/Narrow profile receivers and Narrow senders
- SMPTE ST 2110-30 PCM audio
- SMPTE ST 2110-40 metadata associated with SMPTE ST 2110-20 video stream
- SMPTE ST 2022-6 Transport of High Bit Rate Media Signals (HBRMT) (SDI) over IP Networks
- SMPTE ST 2042 (VC2) low-latency high quality compressed IP transport
- SMPTE ST 2022-7 Class A & D seamless protection switching
- SMPTE ST 2059-1 & -2 precision time protocol
- NMOS IS-04 discovery and registration with group hints tag support
- NMOS IS-05 device connection management
- In-band or out-of-band control of NMOS
- Support of DHCP, LLDP and DNS-SD for easy IP configuration
- Both FC-FEC (Fire Code) and RS-FEC (Reed Solomon IEEE) Forward Error Correction are supported
Signal Monitoring (SM) Features
- 12x4 multiviewer capability with signal monitoring license
SPECIFICATIONS
Inputs and Outputs
Signal Inputs/Outputs
SDI: 16x bidirectional, see configuration table
Electrical:
- 3 Gb/s SDI, SMPTE ST 424
- 1.5 Gb/s HD-SDI, SMPTE ST 292
- 270 Mb/s SDI, SMPTE ST 259-C
Connector/format: HD-BNC/75Ω panel jack on standard connector panel
Ethernet Signal
SFP+ Optical: 2x 50 GbE Ethernet
- Conforms to: IEEE 802.3by – 50 GbE over fiber
SFP+ connected cable: 2x 50 GbE Ethernet
- Conforms to: IEEE 802.3 – 50 GbE over twinaxial cables
Note: SFP type must be ordered in addition to the module.
Controls
Indicators
Power: OK (Green)
CPU: OK (Flashing)
Content Status
Summary: OK (Green)
- Warning (Yellow)
- Error (Red)
Electrical
Standards supported: 1125 (1080)/50p (A), 1125 (1080)/59p (A), 750 (720)/50p, 750 (720)/59p, 1125 (1080)/25i, 1125 (1080)/29i, 625 (576)/25i, 525 (480)/29i
Power Consumption
Module power consumption: 45.5 PR (B Frames)
Essence Processing SDI<>IP Configurations
SDI > IP |
IP > SDI |
Format |
Streams |
SDI Frame Sync |
SD, HD, 3G Modes of Operation |
||||
8 |
0 |
SD (PAL/NTSC) HD (720p/1080i) 3G (1080p) |
1x SDI 1x SMPTE ST 2022-6 1x SMPTE ST 2110-20/-30/-40 |
Yes |
8 |
8 |
No |
||
16 |
0 |
No |
||
0 |
16 |
No |
||
12 |
4 |
No |
||
4 |
12 |
No |
||
8 |
0 |
1x SDI, 1x VC2, 1x SMPTE ST 2110-30/-40 |
No |
|
0 |
8 |
1x SDI, 1x VC2, 1x SMPTE ST 2110-30/-41 |
No |
|
4 |
4 |
1x SDI, 1x VC2, 1x SMPTE ST 2110-30/-42 |
No |
|
UHD Modes of Operation |
||||
2 |
2 |
SD (PAL/NTSC) HD (720p/1080i) 3G (1080p) UHD (2160p) |
1x SDI, 4x SMPTE ST 2110-20/-30/-40 (Single Link, Quad Stream) |
No |
2 |
2 |
4x SDI, 1x SMPTE ST 2110-20/-30/-41 (Quad Link, Single Stream) |
No |
|
2 |
2 |
1x SDI, 1x SMPTE ST 2110-20/-30/-41 (Single Link, Single Stream) |
No |
|
4 |
0 |
1x SDI, 4x SMPTE ST 2110-20/-30/-40 (Single Link, Quad Stream) |
No |
|
4 |
0 |
4x SDI, 1x SMPTE ST 2110-20/-30/-41 (Quad Link, Single Stream) |
No |
|
4 |
0 |
1x SDI, 1x SMPTE ST 2110-20/-30/-41 (Single Link, Single Stream) |
No |
|
0 |
4 |
1x SDI, 4x SMPTE ST 2110-20/-30/-40 (Single Link, Quad Stream) |
No |
|
0 |
4 |
4x SDI, 1x SMPTE ST 2110-20/-30/-41 (Quad Link, Single Stream) |
No |
|
0 |
4 |
1x SDI, 1x SMPTE ST 2110-20/-30/-41 (Single Link, Single Stream) |
No |
MEDIA GALLERY



ORDERING INFORMATION
Order codes for IQH enclosures*
IQUCP5000-2B3
Universal Compute Processor. 16 SDI I/O, 2x 50 GbE I/O on single 100 GbE QSFP connector. Suitable for IQH4B frames
IQUCP5001-3B3
Universal Compute Processor. 16 SDI I/O, 2x 50 GbE I/O on single 100 GbE QSFP connector. Includes IQFAN rear panel for additional cooling in IQH3B frame
IQUCP5002-2B3
Universal Compute Processor. 16 SDI I/O, 2x 50 GbE I/O on QSFP connectors. Suitable for IQH4B frames
IQUCP5003-3B3
Universal Compute Processor. 16 SDI I/O, 2x 50 GbE I/O on QSFP connectors. Includes IQFAN rear panel for additional cooling in IQH3B frames
Software Defined Core Licenses
IQUCP-EP
Essence processing license for SDI to/from IP with synchronization and audio rate adaptation
IQUCP-MV
Signal monitoring license, includes 12x4 multiviewer functionality
SFP Options
FCQ-100GE-SR4
100GBASE-SR short range SFP for MMF
Note: QSFP type must be ordered in addition to the module.
* Although IQ modules are interchangeable between enclosures, their rear panels are enclosure specific. Order codes ‘A’ or ‘B’ may be used when installing modules in a ‘B’ enclosure. However, order code ‘A’ must be used when installing modules in an ‘A’ enclosure. Please take time to ensure that the compatible order code is selected to match the chosen enclosure.