Skip to main content
Login Contact Us

IQMIX40

3G/HD/SD-SDI Multichannel IP Transceiver

The IQMIX40 is a multichannel video-over-IP transceiver developed for use within low-latency and high-bandwidth Ethernet IP networks. Using RTP VSF TR-03 (SMPTE ST 2110), TR-04 and SMPTE ST 2022-6 encoding and encapsulation schemes enables the IQMIX40 to encode or decode up to 16 SDI signals and transport them over two 10 GbE or 40 GbE links (SMPTE ST 2022-7). It provides frame-synchronized SDI outputs and both compressed and uncompressed modes of IP operation.

FEATURES

  • Handles up to 16 SDI signals over dual 10 GbE or dual 40 GbE IP links (dependent on Ethernet rate, SDI signal format and compressed or uncompressed transport mode)
  • Supports configuration of Ethernet links for maximum signal transport using both SFPs or for dual link mode to provide link redundancy as per SMPTE ST 2022-7, and when operating as a receiver will dynamically adapt to any stream presented to it
  • Multiple transport types available for each SDI input including:
    • Compressed IP transport using SMPTE ST 2042 (VC2) low-latency high-quality encoding profile
    • Uncompressed video transport using either VSF TR-03 (SMPTE ST 2110) and TR-04 RTP, or SMPTE ST 2022-6 encapsulation
    • PCM audio using TR-03 & AES67
    • SMPTE ST 2110-40 metadata support via IETF standard “RTP Payload for Ancillary Data”
  • Supports frame-synchronized SDI inputs and outputs referenced to either IEEE-1588v2 (PTP) network timing (compliant with SMPTE ST 2059-2) or via the IQH3B or IQH4B frame’s analog reference bus for Black Burst / tri-level syncs
  • Includes 4K UHD quad link mode for 3G SQD or 2SI signal transport
  • Low delay mode and independent H & V offset available for each channel along with up to 2 frames of video delay, and up to 255 ms of audio delay
  • Supports unicast as well as IGMPv3 source specific multicast, allowing point to point operation or transmission in multicast groups
  • Standards supported:
    • 3G-SDI to SMPTE ST 424/SMPTE ST 425 level A compatible
    • HD-SDI to SMPTE ST 292/SMPTE ST 274/SMPTE ST 296
    • SD-SDI to SMPTE ST 259-C
    • 10G & 40G Ethernet to IEEE 802.3
  • RollCall control and monitoring compatible with standard logging and reporting features

SPECIFICATIONS

Inputs and Outputs

Signal Inputs/Outputs

IQMIX4010-2B3 (SFP+)

  • SDI: 16 x bidirectional, see configuration table

IQMIX4000-2B3 (QSFP)

  • SDI: 4 inputs, 4 outputs, 8 x bidirectional; see configuration table

Electrical:

  • 3 Gb/s SDI, SMPTE ST 424
  • 1.5 Gb/s HD-SDI, SMPTE ST 292
  • 270 Mb/s SDI, SMPTE ST 259-C

Connector/format: HD-BNC/75Ω panel jack on standard connector panel
Input cable length: TBC

Ethernet Signal
SFP+ Optical: 2x 10G Ethernet

  • Conforms to IEEE 802.3ae — 10 Gigabit Ethernet over fiber

SFP+ Optical: 2x 40G Ethernet

  • Conforms to IEEE 802.3ba — 40 Gigabit Ethernet over fiber

SFP+ connected cable: 2x 10G Ethernet

  • Conforms to IEEE 802.3ak — 10 Gigabit Ethernet over twinaxial cables

SFP+ connected cable: 2x 40G Ethernet

  • Conforms to IEEE 802.3 — 40 Gigabit Ethernet over twinaxial cables

Note: SFP/QSFP type must be ordered in addition to the module.

Controls

Indicators

Power: OK (Green)

CPU: OK (Flashing)

Content Status

Summary

  • OK (Green)
  • Warning (Yellow)
  • Error (Red)

Functions

General Specifications

Electrical

Standards supported

Module Power Consumption

37.5 PR (B Frames)

SDI to IP Configurations
IQMIX40 – 40 GbE Config 1 Config 2 Config 3 Config 4 Config 5 Config 6 Config 7
SDI In <> Out 12 > 4 8 <> 8 4 > 12 8 > 0 4 <> 4 0 > 8 8 > 0
Codec Support SMPTE ST 2022-6
TR-03 (2110)
TR-04
SMPTE ST 2022-6
TR-03 (2110)
TR-04
SMPTE ST 2022-6
TR-03 (2110)
TR-04
VC2 VC2 VC2 SMPTE ST 2022-6
TR-03 (2110)
TR-04
Frame Sync I/Ps
IQMIX40 – 10 GbE Config 1 Config 2 Config 3
Config 4 Config 5 Config 6 Config 7
SDI In <> Out 12 > 0 8 <> 8 0 > 12 8 > 0 4 <> 4 0 > 8 8 > 0
Codec Support SMPTE ST 2022-6
TR-03 (2110)
TR-04
SMPTE ST 2022-6
TR-03 (2110)
TR-04
SMPTE ST 2022-6
TR-03 (2110)
TR-04
VC2 VC2 VC2 SMPTE ST 2022-6
TR-03 (2110)
TR-04
Frame Sync I/Ps

ORDERING INFORMATION

IQH Enclosures

IQMIX4010-2B3

3G/HD/SD-SDI Multichannel IP Transceiver. 16 SDI I/O, 2x 10 GbE I/O on SFP+ connectors. Suitable for IQH1A and IQH4B frames

IQMIX4000-2B3

3G/HD/SD-SDI Multichannel IP Transceiver. 8 SDI I/O, 4 SDI inputs, 4 SDI outputs, 2x 40 GbE I/O on QSFP connectors. Suitable for IQH1A and IQH4B frames

IQMIX4011-3B3

3G/HD/SD-SDI Multichannel IP Transceiver. 16 SDI I/O, 2x 10 GbE I/O on SFP+ connectors. Includes IQFAN rear panel for additional cooling in IQH3B frame

IQMIX4001-3B3

3G/HD/SD-SDI Multichannel IP Transceiver. 8 SDI I/O, 4 SDI inputs, 4 SDI outputs, 2x 40 GbE I/O on QSFP connectors. Includes IQFAN rear panel for additional cooling in IQH3B frame

SFP Options

FCS-10GE-SR

10GBASE-SR short range SFP for MMF

FCS-10GE-LR

10GBASE-LR long range SFP for SMF

FCQ-40GE-SR

40GBASE-SR short range QSFP for MMF

FCQ-40GE-LR

40GBASE-LR long range QSFP for SMF

FCQ-40GE-LR4

40GBASE-LR4 long range QSFP for SMF

Note: Fiber SFP type must be ordered in addition to the module.

For more details on enclosure types please refer to the IQ Modular Enclosures datasheet.

DOCUMENTS & DOWNLOADS

DATASHEETS

IQMIX40

Multichannel video-over-IP transceiver developed for use within low-latency and high-bandwidth Ethernet IP networks.

The IQMIX40 is a multichannel video-over-IP transceiver developed for use within low-latency and high-bandwidth Ethernet IP networks. Using RTP VSF TR-03 (SMPTE ST 2110), TR-04 and SMPTE ST 2022-6 encoding and encapsulation schemes enables the IQMIX40 to encode or decode up to 16 SDI signals and transport them over two 10 GbE or 40 GbE links (SMPTE ST 2022-7).

Download

DOCUMENTATION LIBRARY

Further documents

Already know what you're looking for? Click the link below to access our full documentation library

Visit Library
Go back to top