Skip to main content
Contact Us

QSFP+ Pluggable Mid-Range Transceiver Module (ESR4)

40 Gb/s Pluggable Optical Transceiver

The QSFP-40G-ESR4 is a 4-channel pluggable optical transceiver module for mid-range data communication and interconnects applications. The module contains four channels in each direction with 40 Gb/s aggregate bandwidth with each channel operating at up to 10 Gb/s at distances of up to 300 meters (984 ft.) using OM3 fiber and 400 meters on OM4 multimode fibers. The electrical interface uses a 38-contact edge type connector, compliant with SFF-8436. The optical interface uses a 12-fiber MPO connector.

SPECIFICATIONS

QSFP-40G-ESR4 Quick Specifications

Part Number: QSFP-40G-ESR4

Form Factor: QSFP+

TX Optical Wavelength: 850 nm

Distance*1: 300m/984 ft. (OM3), 400m/1,312 ft.*2 (OM4)

Cable Type: MMF

Rate Category: 40GBASE

Interface Type: SR4

Digital Optical Mon. (DOM): Yes

Connector Type: MPO/MTP

Power Consumption: 1.5W

*1 Minimum cabling distance is 0.5 meters (1.64 feet) for -SR4 according to the IEEE 802.3 standard.

*2 Considered an engineered link with maximum 1 decibel loss budget

For specifications parameters definition, please refer to IEEE Std 802.3-2012, IEEE Standard for Ethernet, SECTION SIX, Clause 86 and Annex 86A.

Absolute Maximum Ratings

Parameters Symbols Min Max Unit Remarks
Storage temperature Ts -20 +85 deg.C  
Storage relative humidity RH   85    
Supply voltage Vcc -0.3 +3.6 V  
ESD (HBM) VESD -1000 +1000 V High speed interfaces
-2000 +2000 V Others
Transmitter single end input voltage Vin p-p   1400 mVp-p  



Recommended Operating Conditions

Parameters Symbols Min Typ. Max Unit
Operating case temperature Tc 0   +70 deg.C
Supply voltage Vcc 3.13 3.3 3.47 V
Supply current Icc   350 450 mA
Power supply noise tolerance        100 mVp-p
Bit rate BR   10.3125   Gb/s
Rate tolerance   -100   +100 ppm



Electrical Interfaces

Transmitter Input Specification at TP1

Parameters Min Typ. Max Unit Remarks
Single ended input voltage tolerance -0.3   4 V  
AC common mode input voltage tolerance     15 mVrms  
J2 jitter tolerance     0.17 UI  
J9 jitter tolerance     0.29 UI  
DDPWS     0.07 UI  
Eye mask coordinate: 
X1, X2, Y1, Y2
0.11, 0.31 
95, 350
UI
mV
Hit ratio = 5e-5



Receiver Output Specification at TP4

Parameters Min Typ. Max Unit Remarks
Single ended output voltage -0.3   4 V  
AC common mode output voltage     7.5 mVrms  
J2 jitter     0.42 UI  
J9 jitter     0.65 UI  
Output transition time (20% to 80%) 28     ps  
X1, X2, Y1, Y2 0.29, 0.5
150, 425
UI 
mV
Hit ratio = 5e-5



Optical Interfaces

Transmitter Specification at TP2

(Condition: Tc = 0 to 70° C)

Parameters Min Typ. Max Unit Remarks
Optical wavelength 840 850 860 nm  
RMS spectrum width     0.65 nm  
Extinction ratio 3 4.5 7 dB  
Average launched power -7.6 0.1 2.4 dBm  
Optical modulation amplitude -5.6 0 2.4 dBm  
Optical return loss tolerance     12 dB  
Transmitter eye mask definition {X1, X2, X3, Y1, Y2, Y3} 0.23, 0.34, 0.43, 0.27, 0.35, 0.4   Hit ratio = 5e-5
Average launch power of OFF transmitter, each lane     -30 dBm  



Receiver Specification at TP3

(Condition: Tc = 0 to 70° C)

Parameters Min Typ. Max Unit Remarks
Operation wavelength 840 850 860 nm  
Unstressed sensitivity (OMA)*     -11.5 dBm BER=1e-12
Overload     3 dBm  



* USRS is measured with typical SR4 light source with 1m (3.28 ft.) OM3 fiber

ORDERING INFORMATION

QSFP-40G-ESR4

QSFP+ Pluggable Transceiver Module allows optical interoperability up to 300m (400m) using OM3 (OM4) MMF

DOCUMENTS & DOWNLOADS

DATASHEETS

QSFP+ Pluggable Mid-Range Transceiver Module (ESR4)

The QSFP-40G-ESR4 is perfect for high bandwidth, mid-range data communications with 40 Gigabit hot-swappable port for distances up to 300 meters using OM3 fiber.

Download
Go back to top